Article: KB-12259
How to:
RUN Signal not active external conveyor
Skill required to complete this article: Controls and level is No Skill Level Association.

Question/Problem

RUN Signal not active external conveyor 

 

Environment

Lenze PLC

Transfer Device

iCollector  

 

Answer/Solution

Major Causes:

1.Case was not conveyed completely

2.PE is out of alignment

3.Product felt down on the PE

 

Steps to reset the fault:

1.Clear the PE / Re align  the PE

2.Reset Events.

3.Put ICL into production

 

 

This error is happens when the ICL does not get a RUN signal from the conveyor and you get the "RUN signal not active" error on the web HMI for ICL.

 Once they pushed the stucking case or re-aligned the PE, totes started to feed into ICL

 

Splunk Error

Clear the PE / Re align  the PE. 

On this picture below you can see the tote is blocking the PE, ask onsite Maintenance to push it with a long pole or if it is not possible ask them to do LOTO procedures , turn off the ICL Panel and enter to the I/O channel area to clear or re-align the PE.

 

 

 

Reset Events and hit production button.

 

 

 

 

 

Related items

 

[This section is for attachments and/or links to other items. Attached documents shall be up-to-date, correct and using Honeywell standard templates.]

 

Internal Notes

 

[Section is meant for information only available for internal use. This includes references to internal records, such as Jira tickets, bug numbers, etc.]

***If there is information in this section prior to migration to SalesForce, then it may NOT be published. This information will be fully visible along with all information above.***

 

Reason for confidentiality

 

#NotValidated

[Section is meant for a brief reason for any data recorded in Internal Notes above, or any reason that the general article cannot be released to the public. Can be updated to #Validated once reused and agreed by KCS Contributor]

***If there is information in this section prior to migration to SalesForce, then it may NOT be published. This information will be fully visible along with all information above.***

 

DISCLAIMER:

Information in this document is subject to change without notice and does not represent a commitment on the part of Intelligrated. This information is typical of the questions and general advice given; however, your particular case and circumstances may produce different results or require different recommendations. Therefore, use of this information is not a suitable replacement for contacting Intelligrated Technical Service engineering for specific recommendations and solutions to your application.

 

No part of this article may be reproduced or transmitted in any form or by any means including recording, or information storage and retrieval systems, for any purpose without the express written permission of Intelligrated. All information contained within the article is private and confidential and the sole property of Intelligrated.

 

In no event, shall Intelligrated be liable for any damages whatsoever including, without limitation, damages for loss of business profits, business interruption, loss of business information, or other pecuniary loss, even if Intelligrated has been advised of the possibility of such damages. Because some states do not allow the exclusion or limitation of liability for consequential or incidental damages, the above limitation may not apply to you.

 

Template updated 2022-09-20 kwk Pending approval

 Related Articles
No Related Articles Available.
 Help us improve this article...
What did you think of this article?
poor   excellent
Your Email:
Tell us why you rated the content this way. (optional)
RadEditor - HTML WYSIWYG Editor. MS Word-like content editing experience thanks to a rich set of formatting tools, dropdowns, dialogs, system modules and built-in spell-check.
RadEditor's components - toolbar, content area, modes and modules
   
Toolbar's wrapper 
 
Content area wrapper
RadEditor's bottom area: Design, Html and Preview modes, Statistics module and resize handle.
It contains RadEditor's Modes/views (HTML, Design and Preview), Statistics and Resizer
Editor Mode buttonsStatistics moduleEditor resizer
 
 
RadEditor's Modules - special tools used to provide extra information such as Tag Inspector, Real Time HTML Viewer, Tag Properties and other.
   

 Comments...
No user comments available for this article.
Published on 4/1/2024.
Last Modified on 4/1/2024.
Last Modified by Sourabh Magdum.
Article has been viewed 258 times.
Rated out 0 of 10 based on 0 votes.
Print Article Print Article